TOP 7 best feeder chairs for fishing: features, which one to buy, reviews

Similar ratings:

• 5 best fishing chairs from AliExpress

Modern carp fishing is not complete without a feeder chair. Manufacturers produce many models, but only a few are considered the best. Using them for fishing provides the user with maximum comfort and convenience during the fishing process.

Our review presents the best fishing chairs on the domestic market. The rating takes into account not only factory characteristics and the ability to install various body kits, but also reviews from direct users who are familiar with these models first-hand.

Manufacturing stages

A fishing chair is created in several stages. First of all, this is the creation of a frame, onto which the selected seat material is then stretched. Depending on the design, you will need different amounts of materials, but for the chairs below you need to stock up:

• electric drill for drilling mounting holes;
• hacksaw for metal;
• grinder;
• steel pipes (aluminum ones are suitable for a limited budget) with a diameter of 2 cm - to create the legs of the chair you need 4 cuts of 55 cm, and for the frame and seat - 4 parts of the same length, the back will require three pipes: two 70 cm long, one - 30 cm;
• fasteners - in this case these will be bolts and nuts of drill diameter;
• finishing material - an inexpensive and wear-resistant option for a seat with a backrest would be tarpaulin; if funds allow, you can choose leather;
• rubber pads on the legs of the product;
• primer for metal;
• moisture resistant paint.

There are several simple seat options for feeder fishing that you can easily make yourself in just a few hours.

Simple model

For beginners, you can choose the simplest folding chair for fishing, which will nevertheless be quite comfortable and durable. To create it, two closed loops of metal pipes are required, the further steps are as follows:

1. The pipes are connected crosswise using two bolts with two nuts. For a successful event, it will be necessary for one of the contours to be slightly smaller in width than the other.
2. For the upper part, the seat is made of prepared tarpaulin or leather. From the ends they are wrapped around the tube and sewn from the bottom of the material. This will allow them to be secured as tightly as possible.
3. To prevent the seat from opening too wide, you can attach a limiter; as a rule, this role is successfully performed by the seat itself.

At the very end, another one is attached to one of the arcs using bolts, onto which the fabric is similarly attached. It will act as a non-adjustable backrest.

With adjustable legs and backrest

Unlike the previous option, using the above set of tools and materials you can create an adjustable fishing chair with your own hands. To do this you need to follow these steps:

1. Take 4 pipes for the frame, the same number for the seat.
2. On two pipes, 60 mm are measured from the beginning, and the same from the end. At the marked points, holes are made for two fasteners.
3. In one of the pipes prepared in the previous step, another fastener is mounted at a distance of 90 mm from its beginning.
4. Parts with fasteners are connected by others of the same length. The result will be a rectangle of steel pipes.
5. Two parts of 70 cm each are connected to each other by a pipe of 30 cm. Moreover, the long ones must be parallel, and the short one is placed in their upper part using fasteners into which it is inserted. The design is U-shaped.
6. The product is tightened with bolts and nuts to normal rigidity.
7. The 4 ends of the tubes that remain free are equipped with additional fasteners - one for each. They are equipped with legs that will be adjustable.
8. Each leg is equipped with rubber pads - they will help to better adhere to the surface and thereby prevent slipping.
9. Covering with fabric is done. On each short side, holes are created through which an elastic band is pulled, due to which the material is secured to the frame. The same fastening holes are made on the long sides of the fabric for the seat, and they are tied to the metal using rubber bands.

As a result, the fishing chair will be able to be adjusted due to the presence of fasteners, and the cover will sag under the weight of the owner, anatomically fitting the body. This is a comfortable and durable option, made for winter fishing with your own hands.

Made from polypropylene pipes

Although plastic is not a desirable material to use when creating a fishing chair, a reinforced option, polypropylene, will still work. First, a drawing is created with the required dimensions. Then you should purchase 12 polypropylene tubes of the same length and similar diameter. To connect these elements you will also need a soldering iron.

Stages of making a chair for a PVC boat with your own hands, installation nuances

After everything is prepared, you can start creating a fishing chair with your own hands:

1. A rectangular structure is soldered from four tubes, of which three are required. Additionally, you can secure them with bolts and nuts, or screws, for greater reliability.
2. Two rectangles should be secured as legs and a seat, and the third as a backrest.
3. A seat with a backrest is created from textiles, similar to the previous version of the chair.

This fishing chair will be as comfortable as possible due to the absence of sharp corners.

Manufacturing materials and tools

To make a folding chair without spending large sums on its purchase, you can use different materials. The set of tools and the complexity of the design depend on them. Among the available, practical materials, the following stand out:

1. Chipboard (or natural wood) - its processing and assembly does not require welding or carving tools. This is an environmentally friendly and visually pleasing material, but in operating conditions with high humidity (including fishing), it is not durable.
2. Metal is an excellent option for creating a frame, but it requires special tools (for cutting and welding), as well as the application of a special coating against corrosion. From the point of view of wear resistance and reliability, this is the best material.

Modern modifications of the Papasan chair, tips for assembly and placement
Textiles are used to furnish the seat with a backrest. It is important to choose a moisture-resistant, durable fabric that is easy to care for. Fishing chairs are subject to heavy loads and are used in high humidity conditions, so low-quality material quickly becomes unusable.

It is better not to choose aluminum or plastic. They quickly fail (due to their fragility), and with temperature changes and long-term use they become deformed.

Thus, steel with textiles is an excellent combination for creating a comfortable, durable feeder chair. A homemade chair will be quite heavy, but still mobile. To process steel you will need a grinder, a drill, and a hacksaw. Fastening will be done with bolts and nuts.

Chipboard

Metal

Durable, water-repellent textile

Tools

Fasteners

Finishing

To increase the durability of the feeder chair and maintain its presentable appearance, different coating options are used. They depend on the material used and can be as follows:

1. Wood - treated with an antiseptic composition that actively counteracts mold and mildew. A primer and paint or varnish are also applied on top. This set of procedures will help increase the moisture resistance of the tree, as well as its resistance to temperature fluctuations.
2. Metal - the main problem is rust, which destroys the structure of the pipes and the overall strength of the product. Therefore, anti-corrosion treatment is the main task; painting is also allowed.
3. Plywood (chipboard) - you need to deal with this material in the same way as with wood; antiseptic treatment, priming and painting are carried out.

Types of egg chairs, location options, mounting methods

In order for a folding chair made by yourself to retain its appearance for as long as possible and remain reliable, you need to provide it with maximum care. After finishing fishing, the product should be cleaned of adhering dirt and dust, and wiped off any possible moisture. It must be stored in a dry place.

It is quite easy to make a feeder chair with your own hands. Although this task requires serious preparation and the availability of tools. When choosing the optimal fishing chair, it is best to choose a combination of a steel frame and textile fabric. It will be durable and resistant to negative external factors.

Treat wooden elements with an antiseptic and, if desired, paint them

Apply a special coating to metal parts to protect against rust.

After fishing, always clean the chair from adhering dirt and grass.